Scantech V-1020 Uživatelský manuál

Quick Start Guide VEGA Area Imager V-1020 / V-1020BT Handheld Bar code Scanner

3. Programming Sequence You can set-up your VEGA by scan necessary programming codes for parameters that meet applications. After these scan(s) the

9 4. Scanner Imager Mode The VEGA Area Imager mode allows you to position the hand held scanner beam in any direction, regardless of the orientati

Area mode for Codes With Reflective Surface

11 5. RS232 Parameters for V-1020 5.1 Baudrate Baudrate 38400 <Baudrate 57600> Baudrate 115200

5.2 Data bits Data bits 7 <Data bits 8> 5.3 Stop bits <Stop bits 1&

13 6. USB Parameter USB Mode Attention: The “Set factory default” setting would return to the original default setting inste

7. Bluetooth Setup for V-1020BT 7.1 Set Cradle Interface Barcode Set Cradle Interface Default Barcode （default RS232, 19200, N-8-1） Set Cradle KB

15 7.2 Bluetooth Default Setting Default Setting 7.3 Scanner Server/Client Mode Scanner Server Mode Barcode Scanner Client Mode Barcode

7.4 Sleep Mode <Sleep Mode 1 min. ON> Sleep Mode 10min. ON Sleep Mode OFF

17 7.5 Memory Mode Memory Mode ON <Memory Mode OFF> Memory Read Memory Clear

Copyright © 2009, Scantech-ID BV. This manual is copyrighted, with all right reserved. Under the copyright laws, this manual may not, in whole or i

8. Postambles 8.1 Postamble Postamble None <CR+LF> CR LF <ETX>

19 9. Symbologies 9.1 Enable Symbologies Australian Post ON AZTEC ON BPO ON Canada Post ON CODABAR ON Coda

Codablock F ON CODE 11 ON <CODE 39 ON> CODE 93 ON CODE 128 ON <GS1-128 ON> <DATAMATRIX ON> Dutch Post ON

21 <EAN-8 ON> <EAN-13 ON> <EAN 128 ON> GS1 CC-A/B ON GS1 CC-C ON GS1 DataBar-Omni ON GS1 DataBar-Limited ON

Infomail ON INTERLEAVED 2 of 5 ON Japan Post ON Matrix 2 of 5 ON MaxiCode ON MicroPDF417 ON MSI ON <PDF417 ON&

23 Planet ON PLESSEY ON Postnet ON QR Code ON Standard 2 of 5 ON Sweden Post ON Telepen ON TLC 39 ON

<UPC-A ON> <UPC-E ON> Note: This step does not include codes for all support Barcode symbologies. For a complete overview of suppo

25 10. Test Symbologies Scan one or more of these bar codes to test bar code symbologies you enabled. Codabar Code 39 Code 93 Code 128 DataM

Interleaved 2 of 5 MSI code PDF417 GS1 DataBar Omni directional GS1 DataBar Omni Stacked GS1DataBar Expanded GS1DataBar Expanded Stacked

27 11. Specification 11.1 Readable Symbologies: 1D / Linear codes: EAN/UPC, GS1 DataBar, Code 39, Code 128, UCC/EAN 128, ISBN, ISSN, Matrix 2 of

Quick Start Guide Scantech-ID VEGA

11.3 Physical Characteristics Bluetooth Cradle Weight Approx 150 gr. Material ABS Plastic Connector

29 11.6 Electrical Characteristics (V-1020BT) Battery Li-ion 3.7V / 1400mA Charge Time 4.5 hours Reads per charge 10,000 Cradle LED indicat

Scantech-ID BV Nijverheidsweg Noord 60.34 3812 PM Amersfoort The Netherlands Phone: +31 (0)33 469 84 00 Fax:

Table of contents Chapter 1 Introduction...5 Chapter 2 Quick Start 2.1 Standard Shipment Pack

3 5.3 Stop bit ...12 Chapter 6 USB Parameter………………..………… 13 Chapter 7 Bluetooth Setup for V-

Chapter 11 Specification 11.1 Readable Symbologies...27 11.2 Physical Characteristics...

5 1. Introduction Thank you for purchasing this brand-new designed imager hand held bar code scanner. VEGA is a cutting-edge gun-type Area Imaging

2. Quick Start 2.1 Standard Shipment Package The standard shipment package is provided with the following items: a. VEGA Area Imager Handheld Bar

7 power supply if applicable. Press the RED trigger button at the top side of the unit; aim the bar code, which covered by the LED red light zone. Yo